Question 1

Can the solder wire bracket be attached to the right side? For left handed user.

Accepted Answer

Dear customer，
Thank you for your question here.

Currently, to meet your requirement, you can please consider detaching the right-side helping hand and installing the solder wire bracket to the place.  And a metric screw (M4-0.7x8mm or M4-0.7x10mm flat head)  can help you make the installation more stable.

We believe in listening to what our customers have to say — it’s how we’re able to constantly improve our products and services. Thank you again for bringing this up, we will try our best to provide a better user experience in the next-generation station for left-handed users.

Should you have any questions or require further assistance, please drop us an email at Amazon Messaging System (link is here: https://amzn.to/2mKq0EU). We will respond within 24 hours.

Best regards,
YIHUA OFFICIAL STORE

Question 2

What size are the tips

Accepted Answer

Dear Customer,
Thank you for leaving a question here.

The 926LED-III Digital Soldering Station (Orange) comes with 5 additional tips on top of the stock B-Tip.

Type-I – Sharp conical shape for precision soldering, often used for cellphone/mac repair where components are extremely small. (actual edge diameter is less than 0.5mm)

Type-B – Round conical shape for general soldering, probably the most used tip in soldering as it allows maximum contact between the solder pads and component pin in most of the solder joint shapes. (actual edge diameter is approximately 1.0mm)

Type-K – Knife shape with bigger thermal mass for SMD rework, desoldering. Often used to quickly remove small resistors, PLCC components and more. (blade length of approximately 8mm)

Type D – Flat shape for general soldering, often used in through-hole and many other types of joints. This product comes with the 1.6mm and 2.4mm variants of this tip, hence the name 1.6D and 2.4D.

We recommend selecting the tip that will give you maximum contact to heat up both the component’s pin and the solder pad itself to obtain the best soldering results. You’ll need both the component’s pin and the solder pad to heat up sufficiently, so the solder can form a solid inter-metallic bond with the two, allowing electricity to go through.

On top of that, we recommend using YIHUA compatible tips with a temperature setting of around 662°F （350°C）for most of the soldering applications, however, you can adjust the temperature higher based on personal preference.

Hope this explains your question.

Feel free to drop us a message via Amazon’s Messaging System (link is here: https://amzn.to/2mKq0EU ) if you need further assistance. We are more than happy to help you.

Best Regards,
YIHUA OFFICIAL STORE

Question 3

does it power down when the iron is placed back on the stand?

Accepted Answer

Dear customer,
Thanks a lot for your question here and your attention to this useful soldering station!

This Quality Yihua 926 III Soldering Station comes with a sleep function. (Sleep timer setting : 0/5/10/30mins available). This means that it can be sent to Sleep upon the end of the setting time.

How to achieve this effect?

Do the setting and 5/10/30 mins after the soldering iron stays stationary in its stand, you will find the soldering iron goes to sleep. (0 means no sleep)

Instead of the whole unit powering down, the temperature of the soldering iron, under the setting, drops down to a lower value to reduce the chance of unnecessary damage to the station and greatly save energy!

When it enters sleep,

1.	If the temperature was preset at between 90℃-250℃, the temperature will automatically go to 90℃ which will be maintained.

2.	If the temperature was preset above 250℃, the temperature will automatically go to 200℃ which will be maintained.

To wake it up, there are three ways to choose from:

a.	Shake the soldering iron up and down serveral times.
b.	Press once the the silver & black rotary knob (also a menu button)
or c. Turn the power off and then turn the power on.

Should you have any further questions or require assistance, please drop us an email at Amazon Messaging System(link is here: https://amzn.to/2mKq0EU). We will respond within 24 hrs!

Best regards,
YIHUA OFFICIAL STORE

Question 4

why the solder doesn't melt at 600 degree? I thought temperature should had been at 450 degree F.

Accepted Answer

I originally had mine set to 600F and it melted Lead Free and Leaded Solder just fine.  However, I now run it at 800F because it melts quicker for my soldering needs

Included Components	Soldering Iron, Helping Hands
Number of Channels	1
Upper Temperature Rating	896 Degrees Fahrenheit
Lower Temperature Rating	90 Degrees Celsius
Manufacturer	Guangzhou Yihua Electronic Equipement Co.,Ltd.
Item model number	926LED IIIBK
Product Dimensions	18.54 x 11.43 x 7.11 cm; 921 g
ASIN	B082F1WKP9

YIHUA 926 III 60W Digital Soldering Iron Station, with 2 Helping Hands, 194ºF~896ºF Adjustable Precise Temp, °C/ºF switch, Sleep & Calibration Functions + 6 Extra Solder Tips, Solder sucker &Tweezers

Details

Description

Specifications

Have a Question? See What Others Asked

Common Questions